PHD-11HF-27 hmanga siam a ni

Switch contact emaw Proximity switch (NAMUR) input/relay chhuahna tur a ni

H Serie Backplane Mounting ah hian himna tur a awm a
1 input 1 output a ni

Min rawn biak theih reng e

product chungchang chipchiar takin

Technical parameter a ni

Wiring diagram hmanga siam a ni

Certification pek a ni

Internet atanga thil lachhawng

A tlangpuiin

H serie backplane mounting isolated safety barriers at detection side: PHD-11HF-27, digital input leh output, input leh output pakhat.

Isolated barrier hian hazardous area-a proximity switch leh contact input chu relay contact signal-ah a chantir thei a, safe area-ah a thawn thei bawk.

Output relay ah hian "ON/OFF" situation a selection switch a awm a. Tin, input signal short-circuit emaw open-circuit alarm indication a awm bawk a, circuit hian input sensor tan power a pe a ni.

He product hian independent power supply a mamawh a ni.

Signal status indicator hi output relay hnathawh dan tarlanna atan red leh yellow light-ah dah a ni a, alarming atan a nih chuan light chu a sen a, normal operation laiin light chu yellow a ni.

Supply voltage a awm	20~35VDC, power consumption
Signal input a ni	Switch contact emaw Proximity switch emaw (NAMUR) emaw a awm thei.
Sensor awmna hmuna Supply voltage a awm	8V a ni
Signal input dan tur a ni	A hmuna input current: >2.1mA, it Indication ON; On-site input current:
Output chu hmun him takah a awm	Response time: 20ms, lirthei khalh theihna: 250VAC/2A, 30VDC/2A resistive load hnuaiah
Output chu a tlangpuiin hawn/a tlangpuiin khar contact switching control	DIP switch K1 chu "ON" lam ah dah a ni a, relay output chu "a tlangpuiin khar" a ni.
	DIP switch K1 chu "OFF" lam ah dah a ni a, relay output chu "normally open" ah dah a ni.
	DIP switch K2 chu "ON" lam ah dah a ni a, circuit chuan LFD alarm function sen chu a thlang a.
Line Fault hriatchhuah (LFD) 1.1.	A hmuna input current>7mA, short-circuit alarm (SC) , hmuna input current
Line Fault hriatchhuah (LFD) 1.1.	Switch contact input atan chuan disconnection detection function a mamawh hunah switch tawp pahnihah 22KΩ resistor parallel-a connect tur a ni (A hnuaia wiring diagram-ah hian switch contact II hi en la)
Input leh output awm zat	1 input 1 output a ni
Field hmanrua hman tur	DIN 19234 standard angin Dry contact emaw NAMUR proximity switch emaw a ni thei
Temperature parameter a ni	A hnathawhna hmun: -20°C~+60°C, a dahna hmun: -40°C~+80°C
Relative humidity a awm lo	10%~95% RH ah chuan condensation a awm lo
Dielectric chakna a ni	Intrinsically safe side leh non-intrinsically safe side (≥3000VAC/min) inkar; power supply leh non-intrinsically safe terminal (≥1500VAC/min) inkar a ni.
Insulation a do theih loh	≥100MΩ (input/output/power supply inkar) a ni.
Dimension hrang hrang	A thuk zawng 15.8mm * a zau zawng 104.8mm * a san zawng 116.1mm
Electromagnetic nena inmil theihna	IEC 61326-1 (GB/T 18268) ang chuan IEC 61326-3-1
Puak thei lo chhinchhiahna	A rilru a hah lutuk chuan a rilru a buai em em a
Certification siamtu pawl a ni	CQST(China National Quality Supervision leh Explosion Protected Electrical Products te enfiahna hmun)
Certified parameters (terminal 1-2 inkar): 1.1.	Um:250VAC/DC,Uo=10.5VDC,Io=14mA, A rilru a buai em em a, a rilru a hah em em bawk a. Po=37mW,Co=2.4μF,Lo=165mH.
Installation site mamawh a ni	0 zone with instruments nen a inzawm thei bawk IIA, . IIB, 1000 a ni. IIC gas hlauhawm tak a ni
MTBF	≤100000h a ni

PHD-11HF-27 (1) a ni a, a man pawh a tlawm hle.

PHD-11TC-33A-23-ah a awm bawk

PH-Co series RS422 Control Net bus data optical hmanga siam a ni a, a man pawh a to hle.

PHM-7230 Ex Intrinsically Safe Isolated a ni a, a chhuahna tur hmun leh a hmanna tur hmun chu a inthlau hle.