H Series Backplane Mounting Isolated Safety Barriers
- Terminal Board
- A dang tein chiahmi himnak khamnak
- Signal Isolators
- Surge kilvennak thilri
- Himnak Relays
- A dang tein chiahmi fimthiamnak I/O Modules
- Fimthiamnak Kutka
- Riantuannak Data Optical Transceivers
- Online Dew Point Analyzers
- Data laknak Modules
- HART data thlennak
PHD-11HF-27
A tlangpi in
H series backplane chiahnak ah a dang tein chiahmi himnak khamnak hna cu hmuh khawhnak lei ah: PHD-11HF-27, digital luhternak le chuahnak, luhternak pakhat le chuahnak pakhat lawng.
A dang tein chiahmi khamnak nih ttihnung hmun ah a naihnak thlennak le pehtlaihnak luhternak kha relay pehtlaihnak signal ah a thlen khawh i a himnak hmun ah a kuat khawh.
A chuakmi relay cu "ON/OFF" dirhmun thimnak thlennak he aa tlum. Cun, luhternak signal tawite-circuit asiloah on-circuit ralrin peknak hmelchunhnak a um, circuit nih luhternak sensor caah thazaang a pek.
Hi thilri nih hin amah tein mei a herh.
Signal dirhmun langhtertu cu a sen le a sen in ceunak in chiah a si i chuahmi relay riantuan ning a langhter, ralrin peknak caah a si tikah ceunak cu a sen, a ttha tein riantuan lio ah ceunak cu a sen.
| Supply voltage | 20~35VDC, thazaang hmannak |
| Luhternak hmelchunhnak | Pehtlaihnak thlen asiloah naihnak thlennak (NAMUR) |
| Hmun ah sensor voltage pek | 8V |
| Signal luhternak sining | Hmunhma ah luhtermi thazaang: >2.1mA, a langhternak ON; Hmunhma ah luhternak current: |
A himnak hmun ah chuah | Lehnak caan: 20ms, mawngh khawhnak: 250VAC/2A, 30VDC/2A cu a dohmi thilrit tangah |
| A chuakmi a tlangpi in on/a tlangpi in kharmi pehtlaihnak thlennak uknak | DIP switch K1 cu "ON" lei ah chiah, relay chuahmi "a tlangpi in khar" a si. |
DIP switch K1 cu "OFF" lei ah chiah, relay chuahmi "a tlangpi in on" a si. | |
DIP switch K2 cu "ON" lei ah chiah a si, circuit nih a senmi LFD ralrin peknak riantuannak kha a thim. | |
| Line palhnak hmuh khawhnak (LFD) | Hmunhma luhternak current>7mA, short-circuit ralrin peknak (SC) , hmunhma chung luhternak current |
| Switch pehtlaihnak luhternak caah, tthencheunak hngalh khawhnak riantuannak a herh tikah, 22KΩ resistor cu switch a donghnak pahnih ah aa tluk tein pehtlaih a hau (A tanglei wiring diagram ah switch pehtlaihnak II kha zoh) | |
| Luhtermi le chuahmi zat | 1 luhternak 1 chuahnak |
| Hman khawhmi lo thilri hna | DIN 19234 phunglam ningin a ro cangmi pehtlaihnak asiloah NAMUR naihnak thlennak |
| Khuacaan tahfung | Riantuannak lumnak: -20°C~+60°C, chiahnak lumnak: -40°C~+80°C |
| Aa pehtlaimi lumternak | 10%~95% RH ah ti a luang lo |
| Dielectric thazaang | A chunglei in a himmi lei le a him lomi lei karlak (≥3000VAC/min); thazaang peknak le a him lomi terminal (≥1500VAC/min) karlak ah |
| Insulation doh khawhnak | ≥100MΩ (luhnak/chuahnak/mei thazaang peknak karlak) |
| A kauh ning | A thuhnak 15.8mm * a kauhnak 104.8mm * a sannak 116.1mm |
| Electromagnetic aa tlaknak | IEC 61326-1 (GB/T 18268) ning in, IEC 61326-3-1 |
| A puak kho lomi hmelchunhnak | [Exia Ga]IIC, [Exia Da]IIIC |
| Fehternak bu | CQST(Tuluk Ram puahnak in a himmi electric thilri hna caah tthatnak zohkhenhnak le hneksaknak hmun) |
| Fehtermi parameters (terminal 1-2 karlak): | Um:250VAC/DC,Uo=10.5VDC,Io=14mA, Po=37mW,Co=2.4μF,Lo=165mH. |
| Install tuahnak hmun a herhmi | 0 zone chung i thilri hna he pehtlaih khawh a si IIA, IIB, IIC ttihnungmi gas |
| MTBF | ≤100000h |
PHD-11TC-33A-23
