- Terminal Board
- Jam gwoko kwo ma juketho kende
- Jam poko lanyuth
- Jam tic mi gwoko kwo pa dhanu
- Relays mi gwoko kwo
- I/O Modules ma rieko ma jupoko
- Dhugola ma rieko
- Jam tic ma tiyo ku mac
- Dew Point Analyzers mi intanet
- Module mi nwangu lembe
- HART data converter
Neno wi lembe
Kit lanyuth mi ketho man rwom pare
RTD Code Lanyuth Kabedo mi pimo Kabedo ma nok Lokruok ma atira
1 G53 -50~150°C 20°C 0.2°C/0.1%
2 Cu50 -50~150°C 20°C 0.2°C/0.1%
4 Pt100 -200~850°C 20°C 0.2°C/0.1%
6 Pt1000 -200~850°C 20°C 0.2°C/0.1%
7 Ni1000 -60~250°C 20°C 0.2°C/0.1%
TC 1 K -200~1370°C 50°C 0.5°C/0.1%
2 S -50~1760°C 500°C 1.5°C/0.1%
3 MAN -140~1000°C 50°C 0.5°C/0.1%
4 J -160~1200°C 50°C 0.5°C/0.1%
5 B 250~1800°C 500°C 1.5°C/0.1%
6 T -200~400°C 50°C 0.5°C/0.1%
7 R -50~1760°C 500°C 1.5°C/0.1%
8 N -200~1300°C 50°C 0.5°C/0.1%
| Kit lanyuth mi ketho man rwom pare | |||||
| RTD | Code | Lanyuth | Kabedo mi pimo | Kabedo ma nok | Lokruok ma atira |
| 1 | G53 | -50~150°C | 20°C | 0.2°C/0.1% | |
| 2 | Cu50 | -50~150°C | 20°C | 0.2°C/0.1% | |
| 4 | Pt100 | -200~850°C | 20°C | 0.2°C/0.1% | |
| 6 | Pt1000 | -200~850°C | 20°C | 0.2°C/0.1% | |
| 7 | Ni1000 | -60~250°C | 20°C | 0.2°C/0.1% | |
| TC | 1 | K | -200~1370°C | 50°C | 0.5°C/0.1% |
| 2 | S | -50~1760°C | 500°C | 1.5°C/0.1% | |
| 3 | MAN | -140~1000°C | 50°C | 0.5°C/0.1% | |
| 4 | J | -160~1200°C | 50°C | 0.5°C/0.1% | |
| 5 | B | 250~1800°C | 500°C | 1.5°C/0.1% | |
| 6 | T | -200~400°C | 50°C | 0.5°C/0.1% | |
| 7 | R | -50~1760°C | 500°C | 1.5°C/0.1% | |
| 8 | N | -200~1300°C | 50°C | 0.5°C/0.1% | |
Lembe madongo mi tic
Namba pa yore: 1 ma juketho i iye man 1 ma juwodho woko
Jam miyo mac:
Teko pa mac: 20～35VDC, tic pa mac ≤40mA
(24VDC power supply, 20mA output)
Gwoko teko: Gwoko teko ma dwoko cen
Keth i kabedu ma rac:
Lanyuth mi donjo: RTD, lanyuth pa TC (Nen "Kit lanyuth mi donjo man rwom pa lanyuth)
Turo dhu dhu: Lembe macon ubedo "alarm mi lyethu ma piny", ma jucopo lokoni "alarm mi lyethu ma malu" nikadhu kud i software mi yubu piny
Kabedo mi lanyuth: Kabedo mi pimo ma rwate ku lanyuth ma jucwalo
Kabedo mi pimo: Jatic timo yub ka ebemito piny.
Nyuth i namba mi ngeye nyo kyewo waraga
Thermocouple cold compensation: ±1°C (compensation range -20°C~+60°C)
Thermal resistor excitation current: 250μA
Adwogi pa yore mi gwoko kwo:
Lembe ma wok: 4~20mA
Kero: 0~500Ω (jucopo loko)
Kit voltage ma wok kud i iye, rwom pa kero RL≥330kΩ
LED ma nyutho ler: macol ⸺ ma nyutho teko Wiring diagram
Alarm ma piny L1 uwang; ler mi L2 ma ucungo iwi rwom ma malu uwang.
Ber pa adwogi: nen "Kit mi lanyuth man rwom pare" pi lembe mukende
Saa mi dwoko: 300ms mi tundo 90% pa wel ma tok cen
Lokruok pa lyethu: 0.005% FS/℃
Teko mi gwoko piny: thenge maber man thenge ma ber ungo (≥3000V AC/min)
Ikind kero pa mac man non-intrinsically safe terminals (≥1500V AC/min)
Teko pa lyethu: ≥100MΩ (i kind piny ma wok/woko/maku mac)
Electromagnetic compatibility: Lub IEC 61326-1 (GB/T 18268), IEC 61326-3-1
Saa ma rwinyo: 100000h
Jam tic ma tiyo i tic: thermal resistors ma waya aryo man waya adek,thermocouple sensors
Piny ma mitere pi waya: Waya matek (waya ma nyap) dul: 0.2~2.5mm2
Lat pa waya: 26~14AWG; bor pa poko: 8mm
Poi: 1. Power bus power supply ubedo tic ma jutimo. Jutic umitu gi nyuth yore mi mio mac ka gibe lwongo.
2.Ka itiyo ku waya adek mi thermal resistor, tem ni neno nia waya adek ne gi rom rom.
3.Ka itiyo ku waya aryo mi thermal resistor, safety barrier terminals 4 ku 2 umaku ubed short-circuited.
| Terminal | Thelembe pa tic pa terminal | |||
| 9(A) | Power supply+ | 20~35V DC | ||
| 10(B) | Jam miyo mac- | |||
| RTD 2 waya | RTD 3 waya | TC | ||
| 1 | Cul ma ngic | |||
| 2 | ku 4 ma nok ma gicokiri | Keth- | RTD/TC signal | |
| 3 | Keth+ | Keth+ | Keth+ | |
| 4 | Keth- | Keth- | Keth- | |
| 5 | Output+ | 4~20mA | ||
| 6 | Adwogi- | |||
