Digital Input
- Terminal Board
- Jam gwoko kwo ma juketho kende
- Jam poko lanyuth
- Jam tic mi gwoko kwo pa dhanu
- Relays mi gwoko kwo
- I/O Modules ma rieko ma jupoko
- Dhugola ma rieko
- Jam tic ma tiyo ku mac
- Dew Point Analyzers mi intanet
- Module mi nwangu lembe
- HART data converter
PHD-12TF-277+
Neno wi lembe
Jam gwoko kwo ma juketho kende ku tic mi gwoko kwo pa switch input relay outputs, ma poko man cwalu lembe ma wok kud i switch contacts nyo proximity switches i kabedo ma rac ni kabedo mi gwoko kwo ku output relay nikadhu kud i safety barrier. Nwangu peko mi rwom tiyere nikadhu kud i relay matung tung man nyutre iwi LED ma malu pa module. Dial switch pa module jutiyo kudu pi ketho piny ma wok man ma wok in-phase nyoke reverse control, man bende pi ketho nyo kethu tic pa alarm mi nwangu peko.
Piny eni mitu kero ma tiye kende, ku kero ma tiye kende, input, man output terminals.
| Keth piny i kabedu ma rac | |
| Lanyuth mi ketho | Lok dhanu/jami ma kago |
| Teko pa mac pa sensor | Ikum 8V |
| Kite mi loko | |
| Kite mi ketho/woko: | |
| I kabedo mi ketho lembe kawoni | >2.1mA, adwogi ne cego, nyutho ON; Ka |
| Output normally "Yabe"/"Clos" Contact conversion control | Ka dial switch K1, K3 utiye "ON" side, relay output utiye "Normally closed" Ka dial switch K1K3 utiye "OFF" side, relay output utiye "Normally open" Ka dial switch K2K4 utiye "ON" thenge, circuit yero ma nyutho tic pa LFD alarm |
| Wok i kabedu maber | |
| Lanyuth mawok | Relay |
| Kero mi ringo | 250VAC/2A,30VDC/2A ka juketho i tic ku pek ma tek |
| Saa mi dwoko wang lembe | 20ms |
| Jam tic mi gwoko kum: | |
| Nominal discharge current ln(8/20μs) | 5kA |
| Voltage protection level Up(8/20μs): | 60V(lain ku lain) |
| Voltage protection level Up(8/20μs): | 600V(line to ground) |
| Nimakere ku cik | GB/T18802.21-2016(equivalent to 1EC61643-21:2012) |
| Piny ma pire tek | |
| Voltage mi mio | 20~35VDC |
| Tiyu ku mac | |
| LED ma nyutho | Macol: Lanyuth pa kero Yellow: Relay ma wok woko i kite ma tiyo maber Makwar: Lanyuth pa LFD, lanyuth pa peko mi line |
| Piny ma mako lyethu | Lieth mi tic: -20°C ~ +60°C, Lieth mi kano piny: -40°C ~ +80°C |
| Piny ma ngic | 10%~95% RH epe ku pii |
| Teko mi gwoko piny | Ikind thenge ma ber man thenge ma ber ongo (≥3000VAC/min); ikind kero pa mac ku thenge ma ber ongo (≥1500VAC/min) |
| Teko pa lyethu | 100MΩ(500V DC) (i kind piny ma wok/wok woko/mio teko) |
| Ber pa mac | GB/T 18268 (IEC 61326-1) |
| MTBF | 80000h |
| Piny ma mitere pi waya | Thenge ma lageng ≥ 0.5mm2; Teko pa lyethu ≥ 500V |
| Jam tic mi poto ma tiyo | Jam tic mi tic macalo dry contacts nyoke NAMUR type proximity switch inputs ma lubo cik pa DIN19234 |
Paru: Kethu mac pa rail mi mac ubedo tic ma jutimo kende kende. Jutic umitu
nyuth kit mi mio mac ka ibe lwongo.
Kwayu nen piny ma ju medo i pot karatasi mir 89.
Nwangu peko mi lain (LFD)
Jutic copo yero "ON" thenge pa switch ma malu pa module
mi ketho tic mi nwangu peko man nyuthu alarm nikadhu kud i
ler makwar pa LED. I kabedo ma juketho i iye current>7mA, alarm mi circuit ma nok (SC);
I kabedo ma juketho i iye current
lembe ma jukwanu mito tic mi nwangu peko (waya utur, ma nok
circuit), 22k Ω resistor umaku juketh i parallel i thenge ario zoo
pa switch, man 680 Ω resistor umaku juketh i rwom acel (calu
nen i cal pa waya pa switch II).
PHD-11TC-33A-23
PHD-12TF-277+