Gin ma ki keto i cim
- Terminal Board
- Gin ma gengo gwok ma ki poko
- Gin ma poko lanyut
- Jami ma gwoko kom ki i mac
- Jami ma gwoko kuc
- I/O Modules ma ki poko gii ma ryek
- doggola ma ryek
- Jami ma ki lwongo ni Industrial Data Optical Transceivers
- Jami ma ki lwongo ni Dew Point Analyzers ma tye i intanet
- Jami ma ki tiyo kwede me nongo ngec
- HART gin ma loko ngec
PH D-22T F-2727
Neno matut
Gin ma gengo gwok ma ki keto i kom gin ma ki nongo: PHD-22TF-2727, gin ma ki keto i cim ki ma ki kwanyo, gin ma ki keto ki gin ma ki kwanyo.
Gin ma ki keto ni twero loko gin ma ki lwongo ni proximity switch ki gin ma ki keto i kabedo ma tye ki peko me doko gin ma ki lwongo ni relay contact signal ki cwalo ne kama ber.
Gin ma ki lwongo ni output relay ni ki keto iye gin ma ki yero me "ON/OFF" Medo ikom meno, tye gin ma ki keto me nyutu ni mac ma oyabe onyo ma oyabe, gin ma ki lwongo ni signal ni miyo teko bot gin ma ki keto iye.
Gin ni mito teko ma aa ki woko ma romo 20-35VDC.
Gin ma nyutu kit ma lanyut ni tye kwede ki keto i mac makwar ki makwar me nyutu kit ma gin ma ki cwalo ni tye ka tic kwede, ka tye me miyo lworo ci mac ni bedo makwar, i kare me tic maber mac ni bedo makwar.
* Kit me miyo teko pa bac, nen karatac ma ki medo pi ngec mukene.
| Mi teko me mac | 20~35VDC, tic ki teko |
| Gin ma ki keto me donyo | Lok lok/lok me bedo cok |
| Mi kero me mac ki tung lacuc i kabedo ni | 8V |
| Kit me keto lanyut | Kit ma ki keto kwede: >2.1mA, man tere ni ON; teko ma ki keto i kabedo: |
| Lok hysteresis: 0.2ms | |
| Kit ma ki cwalo kwede gin ma ki cwalo ni | Cawa me gamo: 20ms, kero me dwoyo: 250VAC/2A, 30VDC/2A i te teko ma ki keto. |
| Gin ma ki cwalo "ON"/"OFF" ma ki loko kwede | Ka gin ma ki lwongo ni dial switch K1, K3 tye i "ON" tung, gin ma ki cwalo ni tye "OFF". |
| Ka gin ma ki lwongo ni dial switch K1, K3 tye i "OFF" tung, gin ma ki cwalo ni tye "ON". | |
| Ka gin ma ki lwongo ni dial switch K2, K4 tye i "ON" tung, gin ma ki lwongo ni circuit ni yero ma nyutu tic pa mac ma ki lwongo ni red light relay. | |
| Nyutu tic pa alarm ma ki lwongo ni alarm | On-site input current > 7mA, short-circuit alarm (SC), on-site input current |
| Pi keto jami ma ki keto i kom gin ma ki lwongo ni switch, ka gin ma ki lwongo ni disconnection detection function mite, 10KΩ resistor omyera ki ket i kom gin ma ki lwongo ni parallel i agiki me switch (Nen switch contact II i cal ma piny kany) | |
| Namba me keto ki kwanyo | 2 donyo 2 kato woko |
| Jami ma ki tiyo kwede i gang tic | Dry contact onyo NAMUR proximity switch ma lubu cik me DIN 19234. |
| Lapim me lyeto | Lyeto me tic: -20°C- +60°C, lyeto me gwoko: -40°C- +80°C |
| Kit ma yamo ngiic kwede | 10%~95%RH labongo pii ma mol |
| Teko pa dielectric | I kin dul ma tye maber ki dul ma pe tye maber (≥ 3000VAC/min); i kin teko ma ki miiyo ki gin ma ki lwongo ni non-intrinsically safe terminal (≥ 1500VAC/min) |
| Gin ma gengo lyeto | ≥100MΩ (i kin gin ma ki keto/ki kwanyo/miyo teko) |
| Kit ma woko | Pek 12.5mm x lac 108mm x bor 118mm |
| Kit ma jami ma mako mac rwate kwede | Malube ki IEC 61326-1(GB/T 18268), IEC 61326-3-1 |
| Lanyut ma gengo mwoc | [Exia Ga]IIC |
| Karatac me tic maber | SIL3 malube ki IEC 61508 EN 61511 cik |
| Dul ma miiyo twero | CQST(China National Quality Supervision and Test Center for Explosion Protected Electrical Products) |
| Jami ma ki moko (ikin terminal 3-4,1-2) | Um=250V Uo=10.5V I=15mA Co=1.7μF Lo=150mH Po=39.4mW |
| Jami ma mite i kabedo me keto ne | Ki twero kubu ki jami ma tye i 0 ki ⅡA, ⅡB, ⅡC yamo marac |
| MTBF | ≤100000h |
PHD-11TC-33A-23
PHD-22TF-2727