- Terminal Board
- A dang tein chiahmi himnak khamnak
- Signal Isolators
- Surge kilvennak thilri
- Himnak Relays
- A dang tein chiahmi fimthiamnak I/O Modules
- Fimthiamnak Kutka
- Riantuannak Data Optical Transceivers
- Online Dew Point Analyzers
- Data laknak Modules
- HART data thlennak
PH6203-2A2B-NP
A tlangpi in
PH6203-2A2B-NP cu NPN le PNP phun himnak mei vannak puan luhternak caah aa tlakmi himnak relay control module a si, himnak relay caah a tlangpi in aa onmi (NO) himnak chuahnak pehtlaihnak 2 le a tlangpi in kharmi (NC) bawmtu chuahnak pehtlaihnak 2 he. Channel pahnih riantuannak a bawmh i kut in asiloah amah tein remh khawh a si.
Technical data
| Thazaang peknak sining | |
| Thazaang peknak | 24V DC |
| Atu hmanmi | ≤90mA(24V DC) |
| Voltage tuar khawhnak | 0.85～1.1 |
| Luhtermi sining | |
| Hri doh khawhnak | ≤ 15 Ω |
| Luhtermi current | ≤50mA(24V DC) |
| Luhnak thilri | NPN, PNP phun ceunak thilri hna |
| Pehtlaihnak zat | 2NO+2NC |
| Pehtlaihnak thilri | AgSnO2+0.2 μmAu |
| Pehtlaihnak phun | Hramhram in lamhruainak |
| Pehtlaihnak fuse kilvennak | 10A gL/gG, NEOZED (a tlangpi in aa ongmi pehtlaihnak) 6A gL/gG,NEOZED(a tlangpi in aa kharmi pehtlaihnak) |
| Thlennak thazaang (EN 60947-5-1) | AC-15,5A/230V;DC-13,5A/24V |
| Seh thilri nunchung | voi 107 nak tam |
| Caan sining | |
| On tlaihnak | |
| Amah tein remh tthan | ≤300ms |
| Kut in Reset | ≤150ms |
| Thazaang tlawmternak ah tlaihnak | |
| Emergency ngolnak riantuannak | ≤30ms |
| Mei a rawk | ≤100ms |
| Damnak caan | |
| Emergency ngolnak riantuannak | ≤ 30ms |
| Mei a rawk | ≤100ms |
| Supply caan tawite ngolternak | 20ms |
| himnak hngalhternak | |
| Riantuannak tlukruannak (PL) | PLe cu EN ISO 13849 he aa tlak |
| Himnak phun (Cat.) | Cat.4 cu EN ISO 13849 he aa tlak |
| Riantuan caan (TM) | EN ISO 13849 he aa tlakmi kum 20 |
| Zawtnak thlopnak (DC/DCavg) | 99% cu EN ISO 13849 he aa tlak |
| Himnak Diknak Tlukruannak (SIL) | SIL3 cu IEC 61508, IEC 62061 he aa tlak |
| Hardware palhnak tuar khawhnak (HFT) | 1 cu IEC 61508, IEC 62061 he aa tlak |
| A himmi tlamtlin lonak cheu (SFF) | 99% cu IEC 61508, IEC 62061 he aa tlak |
| A ttihnungmi tlamtlin lonak (PFHd) | 3.09E-10/h IEC 61508,IEC 62061 he aa tlak |
| Dinternak Category | 0 cu EN 60204-1 he aa tlak |
| 10% a tlangpi in thilri hna i a ttihnungmi rawhnak caan (B10d) | |
| DC13,Ue=24V | Ie 5A 2A 1A Cycle 300,000 2,000,000 7,000,000 |
| AC15,Ue=230V | Ie 5A 2A 1A Cycle 200,000 230,000 380,000 |
Pawngkam sining
Electromagnetic aa tlaknak EN 60947, EN 61000-6-2, EN 61000-6-4 he aa tlak
Hninhnak a tam ning 10Hz~55Hz
Hninhnak a ngan ning 0.35mm
Pawngkam lumnak -20 ℃~+60 ℃
Chiahnak lumternak -40 ℃~+85 ℃
Aa pehtlaimi lumternak 10% in 90% tiang
Sannak ≤ 2000m
Insulation sining
Electric thianhnak le tliknak hlatnak EN 60947-1 he aa tlak
Voltage tlukruannak III
Thil thurhnawmhnak tlukruannak 2
Huhphenhnak tlukruannak IP20
Insulation thazaang 1500V AC, minutes 1
Rated insulation voltage 250V AC
Rated impulse voltage 6000V(1.2/50us)
| Pawngkam sining | |
| Electromagnetic aa tlaknak | EN 60947, EN 61000-6-2, EN 61000-6-4 he aa tlak |
| Hninhnak a tam ning | 10Hz~55Hz |
| Hninhnak a ngan ning | 0.35mm |
| Pawngkam lumnak | -20 ℃~+60 ℃ |
| Chiahnak lumternak | -40 ℃~+85 ℃ |
| Aa pehtlaimi lumternak | 10% in 90% tiang |
| Sannak | ≤ 2000m |
| Insulation sining | |
| Electric thianhnak le tliknak hlatnak | EN 60947-1 he aa tlak |
| Voltage tlukruannak | III |
| Thil thurhnawmhnak tlukruannak | 2 |
| Huhphenhnak tlukruannak | IP20 |
| Insulation thazaang | 1500V AC, minutes 1 |
| Rated insulation voltage | 250V AC |
| Rated impulse voltage | 6000V(1.2/50us) |
Lenglei tahfung
Riantuannak Block Diagram
A tlangpi in hmanmi
Hri hrennak hmanthlak
(1) Thilri hri nih Pluggable pehtlaihnak terminal a hman;
(2) A luhnak lei hri i a nemmi dar tthencheunak hmun cu 0.5mm2 nak tam a si lai, cun chuahnak lei cu 1mm2 nak tam a si lai;
(3) A langmi hri sauhnak cu 8mm hrawng a si, cucu M3 hri in khar a si;
(4) A chuakmi pehtlaihnak nih a za tawk in fuse kilvennak pehtlaihnak a pek a hau;
(5) Dar hri cu a tlawmbik 75 °C a simi pawngkam lumnak kha a tuar khawh a hau;
(6) Terminal screws nih riantuan ningcang lo, lumternak, tbk. a chuahter khawh. Cucaah, a langhtermi torque ning in hren. Terminal screw tightening torque 0.5Nm.
Chiahnak
Himnak relay pawl cu a tlawmbik IP54 kilvennak tlukruannak he control cabinet ah chiah ding a si. Cu lio ah, chiahnak le hmannak cu GB 5226.1-2019 "Mechanical le Electrical Himnak - Mechanical le Electrical Thilri - Part 1: General Technical Conditions" he aa pehtlaimi phunglam hna he aa tlak awk a si.
PH6203-2A2B-NP series himnak hri pawl cu DIN35mm lamhruaitu hri he an chiah dih hna. Install tuah ningcang cu a tanglei bantuk in a si
(1) Thilri cunglei donghnak kha lamhruaitu hri cungah hren;
(2) Thilri a tanglei bik kha lamhruaitu hri chungah hnuh.
Hrawh
Instrument panel a tanglei bik ah a ummi thir hri chungah screwdriver (hriamnam kauhnak ≤ 6mm) khumh;
Screwdriver kha cunglei ah hnuh law thir hri kha tanglei ah hnuh;
Instrument panel kha cunglei ah hnuh law lamhruaitu hri chungin chuahter.
Lungthin pek
Thilri chiahnak, thilri min cazin model, le a konglam hna cu cawknak hnatlaknak he aa tlak maw tlak lo ti kha zohfel;
Himnak hri chiah le hman hlanah, hi cauk hi ralring tein rel;
Biahalnak na ngeih ahcun, Beijing Pinghe Technical Support Hotline kha 400 711 6763 ah pehtlaihnak tuah;
Himnak relay cu a tlawmbik IP54 kilvennak tlukruannak he control cabinet ah chiah ding a si;
Thilri caah 24V DC thazaang peknak, le 220V AC thazaang hmannak cu fakpi in kham a si;
Fim
(1) Zaangfahnak tein himnak relay himnak riantuannak cu a ttha maw ttha lo, cun circuit asiloah a hramthawknak kha hrawh asiloah hrial a si timi hmelchunhnak a um maw um lo ti kha zungzal in zohfel;
(2) Aa pehtlaimi himnak phunglam kha zulh law hi lamhruainak cauk chung i lamhruainak ningin riantuan, cu lo ahcun thihnak tiang a chuahter khomi accident asiloah minung le thilri sunghnak a chuahter khawh;
(3) Thilri pawl cu sehzung in an chuah hlanah fek tein zohfelnak le tthatnak zohfelnak an tuah cang. Thilri pawl nih ttha tein rian an ttuan lo ti na hmuh i a chunglei module a palh tiah na lunghrinh ahcun, a nai bikmi agent kha pehtlaihnak tuah asiloah thiamnak lei bawmhnak hotline 400 711 6763 kha direct in pehtlaihnak tuah.
(4) A kuat ni in kum ruk chung ah, a tlangpi in hman lio ah thilri tthatnak kong buainak vialte cu Pinghe nih man loin a remh lai.