- Terminal Board
- Jam gwoko kwo ma juketho kende
- Jam poko lanyuth
- Jam tic mi gwoko kwo pa dhanu
- Relays mi gwoko kwo
- I/O Modules ma rieko ma jupoko
- Dhugola ma rieko
- Jam tic ma tiyo ku mac
- Dew Point Analyzers mi intanet
- Module mi nwangu lembe
- HART data converter
PH6102-2A2B(M)
Neno wi lembe
PH6102-2A2B (M) ubedo module mi gwoko kwo ma ber pi button mi juku peko, dhugola mi gwoko kwo, ku 2 normally open (NO) safety output contacts man 2 normally closed (NC) auxiliary output contacts pi safety relays. Ekonyo tic ku channel acel man aryo, dwoko piny ku cing, man etiye ku tic mi gwoko circuit ma nok ikind channel.
Lembe mi tic
| Kite pa kero pa mac | |
| Mio mac | 24V DC/AC |
| Tic ma kawoni | ≤90mA(24V DC) |
| ≤240mA(24V AC) | |
| Voltage tolerance | 0.85～1.1 |
| AC frequency | 50Hz～60Hz |
| Kite ma juketho kudu | |
| Cwiny pa waya | ≤ 15 Ω |
| Keth kawoni | ≤50mA(24V DC) |
| Jam tic mi ketho lembe | E-Stop buttons, safety gate |
| Kite pa adwogi | |
| Wel mi dhanu | 2NO+2NC |
| Jam tic mi rwate | AgSnO2+0.2 μmAu |
| Kit wec | Telo wi dhanu ku tego |
| Gwok pa fuse | 10A gL/gG, NEOZED (normally open contact) 6A gL/gG, NEOZED (normally closed contact) |
| Kero mi loko (EN 60947-5-1) | AC-15,5A/230V;DC-13,5A/24V |
| kwo pa cuma | makadhu wang 107 |
| Kite pa sawa | |
| Delay mi caku tic | |
| dwoko piny ku cing | ≤150ms |
| Delay-on de-energisation | |
| Juko tic pio pio | ≤30ms |
| Tur pa mac | ≤100ms |
| Saa mi dwoko piny | |
| Juko tic pio pio | ≤30ms |
| Tur pa mac | ≤100ms |
| Mi kony ma nok | 20ms |
| certificate mi bedo ber | |
| Kite mi tic (PL) | PLe lubu EN ISO 13849 |
| Dul mi gwoko kuc (Cat.) | Cat.4 lubu EN ISO 13849 |
| Saa mi tic (TM) | 20 oro nimakere ku EN ISO 13849 |
| Lembe ma jutimo ikum two (DC/DCavg) | 99% lubu EN ISO 13849 |
| Kite mi gwoko kwo (SIL) | SIL3 lubu IEC 61508, IEC 62061 |
| Hardware Fault Tolerance (HFT) | 1 lubu IEC 61508,IEC 62061 |
| Safe failure fraction (SFF) | 99% lubu IEC 61508, IEC 62061 |
| Lembe ma copo bedu rac (PFHd) | 3.09E-10/h lubu IEC 61508,IEC 62061 |
| StopCategory | 0 rwate ku EN 60204-1 |
| 10% wel ma romo pa ret ma rac pa piny moko (B10d) | |
| DC13,Ue=24V | Ie 5A 2A 1A Cycles 300,000 2,000,000 7,000,000 |
| AC15,Ue=230V | Ie 5A 2A 1A Cycles 200,000 230,000 380,000 |
Kite ma woko
Cal pa dul ma tiyo
Tic ma rwinyo
Cal pa waya
(1) Waya pa jam tic tiye ku terminal ma jucoko i Pluggable;
(2) Kabedo mi copper mayom pa waya mi dhugola ucikere ni bedu malac uloyu 0.5mm2, man dhugola mi wok ucikere ni bedu malac uloyu 1mm2;
(3) Bor pa waya ma juwodho ubedo 8mm, ma jugwoko ku M3 screws;
(4) Contacts ma wok woko umaku ubed ku rwom ma romo mi gwoko fuse;
(5) Copper conductor umaku ucung ikum lyethu ma romo 75 °C;
(6) Terminal screws copo nyayu tic marac, lyethu, man mange. Pieno, kwayu iket tek nimakere ku torque ma jukwanu. Terminal screw tightening torque 0.5Nm.
Kethu piny
Relays mi gwoko kwo umaku juketh i cabinet ma gwoko ku IP54. Ikinde marom, ketho man tic kudu umaku ulub cik mi GB 5226.1-2019 "Gwok pa cuma man mac - Jam tic man mac - Thenge mir acel: Lembe ma mako mac".
PH6102-2A2B(M) series safety relays juyike ku DIN35mm guide rails. Lembe mi ketho piny utiye ma e
(1) Keth cing ma malu pa jam tic ikum guide rail;
(2) Cwal thenge ma piny pa jam tic i guide rail.
Turo piny
Med screwdriver (lac pa pala ≤ 6mm) i latch mi cuma ma piny pa jam tic;
Cwal screwdriver malo man i lok piny;
Twal panel mi jam tic malu man woko kud i guide rail.
Winjo
Kwayu nen ka yub pa piny, lanyuth pa piny, man lembe ma jukwanu urombo ku karatasi mi wil;
Mapodi i ketho man itiyo ku safety relays, som buku eni maber;
Ka itiye ku penji moku ci, cwal cing ikum Beijing Pinghe Technical Support Hotline i namba 400 711 6763;
Relay mi gwoko kwo ucikere ni bedu i cabinet ma gwoko ku IP54;
Jam tic eni tiyu ku mac ma 24V, man tic ku mac ma 220V AC jukwero;
Gwoko
(1) Kwayu ibed inen kare ku kare ka tic pa safety relay utiye maber, man ka nyo lanyuth moko utiye ma nyutho nia circuit nyo original ne juturo nyo juwotho;
(2) Kwayu ilub cik mi gwoko kwo man itim tic nimakere ku cik ma nwangire i buku mi ponji eni, tek epe ecopu nyayu ret ma rac nyo tho pa dhanu man piny peri;
(3) Piny ma juyubu ukadhu kud i nen pa piny man nen pa ber pa piny ne mapodi juwok kud i factory. Ka inwango nia piny ne timo ngo tic maber man iparu niya module mi iye utiye ku peko, kwayu ilok ku jara tic ma ceng kudu nyo ilok ku namba mi kony mi tic.
(4) I kind oro abusiel nicaku i nindo mi cwalo piny, peko ceke mi ber pa piny i kare ma jutiyo kudu maber jubi yiko ku Pinghe ma cul ope.