- Terminal Board
- Jam gwoko kwo ma juketho kende
- Jam poko lanyuth
- Jam tic mi gwoko kwo pa dhanu
- Relays mi gwoko kwo
- I/O Modules ma rieko ma jupoko
- Dhugola ma rieko
- Jam tic ma tiyo ku mac
- Dew Point Analyzers mi intanet
- Module mi nwangu lembe
- HART data converter
PH6001-1B
Neno wi lembe
PH6001-1B ubedo piny ma gwoko kwo pa dhanu, ma ber pi poko man loko DI/D0 i SIS system. Etiye ku 1 normally closed (NC) contact, man circuit pare mi iye tiyo ku diro mi Fail-safe, diro mi triple redundancy man diro mi gwoko welding.
Lembe mi tic
| Kite pa mac: | |
| Jam miyo mac: | 24V DC |
| Rweny ma kawoni: | ≤35mA(24V DC) |
| Voltage range: | 16V~35V DC nonpolarity |
| Kite ma jukyewo kudu: | |
| Keth kawoni: | ≤ 35mA (24V DC) |
| Cwiny pa waya: | ≤ 15 Ω |
| Jam tic mi ketho: | SIS system DI/DO signal matching |
| Kite ma wok kudu: | |
| Namba pa ju ma juweco kudu: | 1NC |
| Piny mi lok: | AgSnO2 |
| Gwok pa fuse: | 5A (gwok pa fuse ma iye) |
| Kabedo mi wec: | 5A/250V AC; 5A/24V DC |
| Kwo pa cuma: | makadhu wang 107 |
| Kite pa sawa: | |
| Delay mi caku tic: | ≤ 30ms |
| Delay-on de-energisation: | ≤ 30ms |
| Saa mi dwoko piny: | ≤ 30ms |
| Mi kony ma nok: | 20ms |
| certificate mi bedo ber | |
| Kite mi gwoko kwo (SIL): | SIL3 lubu IEC 61508 |
| Hardware Fault Tolerance (HFT): | 0 rwate ku IEC 61508 |
| Safe failure fraction(SFF): | 99% lubu IEC 61508 |
| Lembe ma copo bedu rac (PFHd): | 1.00E-09 /h lubu IEC 61508 |
| StopCategory: | 0 rwate ku EN 60204-1 |
| 10% wel ma romo pa ret ma rac pa piny moko (B10d): | |
| Voltage ma juporo 24VDC, L/R=7ms: | Ie 2A 1A 0.5A Cycles 180,000 300,000 400,000 |
| Rated Voltage 230VAC , cos φ= At 0.4: | Ie 2A 1A 0.5A Cycles 500,000 580,000 600,000 |
| Kite pa kabedu | |
| Ber pa mac: | rwate ku EN 60947, EN 61000-6-2, EN 61000-6-4 |
| Pol pa yeng yeng: | 10Hz~55Hz |
| Teko pa yeng yeng: | 0.35mm |
| Liet pa piny: | -20 ℃~+60 ℃ |
| Lieth mi kano piny: | -40 ℃~+85 ℃ |
| Piny ma ngic: | 10% nicidho 90% |
| Bor: ≤ 2000m | ≤2000m |
| Kite mi gwoko piny | |
| Kabedo pa mac man bor pa creepage: | lubo EN 60947-1 |
| Overvoltage level: | III |
| Kite mi pollution: | 2 |
| Kite mi gwoko: | IP20 |
| Teko pa lyethu: | 1500V AC, dakika acel |
| Voltage mi lyethu: | 250V AC |
| Rated impulse voltage: | 6000V (1.2/50us) |
Cal pa waya
Cal pa dul ma tiyo
Tic ma rwinyo
Cal pa waya
(1) Waya pa jam tic tiye ku terminal ma jucoko i Pluggable;
(2) Kabedo mi copper mayom pa waya mi dhugola ucikere ni bedu malac uloyu 0.5mm2, man dhugola mi wok ucikere ni bedu malac uloyu 1mm2;
(3) Bor pa waya ma juwodho ubedo 8mm, ma jugwoko ku M3 screws;
(4) Contacts ma wok woko umaku ubed ku rwom ma romo mi gwoko fuse;
(5) Copper conductor umaku ucung ikum lyethu ma romo 75 °C;
(6) Terminal screws copo nyayu tic marac, lyethu, man mange. Pieno, kwayu iket tek nimakere ku torque ma jukwanu. Terminal screw tightening torque 0.5Nm.
Kethu piny
Relays mi gwoko kwo umaku juketh i cabinet ma gwoko ku IP54.
PH6001-1A series safety relays juyike ku DIN35mm guide rails. Lembe mi ketho piny utiye ma e
(1) Keth cing ma malu pa jam tic ikum guide rail;
(2) Cwal thenge ma piny pa jam tic i guide rail.
Turo piny
Med screwdriver (lac pa pala ≤ 6mm) i latch mi cuma ma piny pa jam tic;
Cwal screwdriver malo man i lok piny;
Twal panel mi jam tic malu man woko kud i guide rail.
Winjo
Kwayu nen ka yub pa piny, lanyuth pa piny, man lembe ma jukwanu urombo ku karatasi mi wil;
Mapodi i ketho man itiyo ku safety relays, som buku eni maber;
Ka itiye ku penji moku ci, cwal cing ikum Beijing Pinghe Technical Support Hotline i namba 400 711 6763;
Relay mi gwoko kwo ucikere ni bedu i cabinet ma gwoko ku IP54;
Jam tic eni tiyu ku mac ma 24V, man tic ku mac ma 220V AC jukwero;
Gwoko
(1) Kwayu ibed inen kare ku kare ka tic pa safety relay utiye maber, man ka nyo lanyuth moko utiye ma nyutho nia circuit nyo original ne juturo nyo juwotho;
(2) Kwayu ilub cik mi gwoko kwo man itim tic nimakere ku cik ma nwangire i buku mi ponji eni, tek epe ecopu nyayu ret ma rac nyo tho pa dhanu man piny peri;
(3) Piny ma juyubu ukadhu kud i nen pa piny man nen pa ber pa piny ne mapodi juwok kud i factory. Ka inwango nia piny ne timo ngo tic maber man iparu niya module mi iye utiye ku peko, kwayu ilok ku jara tic ma ceng kudu nyo ilok ku namba mi kony mi tic.
(4) I kind oro abusiel nicaku i nindo mi cwalo piny, peko ceke mi ber pa piny i kare ma jutiyo kudu maber jubi yiko ku Pinghe ma cul ope.